I have a Bobcat T590 with 7 pin. I'm need a harness for Bobcat 6 way dozer blade which has 14 pin harness.

You require 4 solenoid drivers.

CLICK HERE FOR THE CORRECT CONTROLLER

What product would I need to operate a wolverine power angle broom with a 2016 T595 Bobcat ( w/ 7 Pin )? I believe this is correct, just want to make sure.

CLICK HER FOR THE CORRECT KIT

my dealer code is not working trying to get some harnesses on order Central Nebraska Bobcat

All codes were cancelled for this year.  You need to send your reseller certificate in and you you will receive a new code.

I have a Erskine 2010 Snow blower and it came with a pistal grip connection cord. Would like to convert the snowblower to a Bobcat 7 pin to run on my T595 Bobcat. Do you offer a harness that will work for this?

Here is the harness for the blower.

CLICK HERE

Here is the controller for the machine.

CLICK HERE

would this be able to run a 12v motor for snow blower chute direction (New holland Blower). Just needs full power 12 feeds as far as I know. The blower has a polarity reversing relay on it. I would need constant power and ground then 2 signal wires to work as is. If you have another way to make it work that would be grreat. I would need extra ends to hook up 3 attachments with single solenoids as well.

I built this product for bi-directiona controlled power.

CLICK HERE

When can I order one?

Should be by next week. We are finally catching up.

Thank you for your patience.

When do you expect these SG-CB-2000A-100 - GENIUS - 7 PIN CONTROLLER FOR BOBCAT® LOADERS - 2 PORT | SKID STEER GENIUS for me to order one?

They should be loaded now. If not any day they will pop up.

Please let me know when these are back in stock need one soon as possible

Working as fast as we can.  I am redesigning with another group to alleviate these issues once and for all.  I am as fed up with this supply chain as anyone as it has been killing us for 3 years.  There are products already redesigned on the site that I have been working on.  These are the last to go through a new design.

Can you notify me when this is available?

Send us your details and we will notify you.

How long until one is available?

This month more will be added.  The problem is that they sell out too quickly.

Is the SG-CB-2000A-100 - GENIUS the correct kit to connect a 2017 T650 Bobcat with a Double Discharge LandHonor Cement Mixer ? One solenoid.

Yes.  It should be similar to one of these.

Click here

and

Click here

Trying to order just 8-10 of the SG-CB-2000A-100. When will be able to order more again?

We add some every week but they sell out fast.  Emeil back and we can add you to the priority list.

SG-CB-2000A-100 - GENIUS - 7 PIN CONTROLLER FOR BOBCAT® LOADERS - 2 PORT what's the eta on these

We add a few each week but they sell out instantly.  Send your name and email and we can add you to the contact list.

I have one of these controllers and I believe the box is not working any more and need a new one. It looks like you are out of stock. The box itself is showing 500 ohmns of resistance through the box is that normal. There is power to the box but the solenoids on the plow are not lighting up and nothing fuctioning. Some how the box got a hole in it and wondering if there was some corosion in it. Are you expecting more in stock soon?

Yes, we are getting more stock weelky but they sell out quickly.  If you forward your information, we can add you to the list.

How long do you expect to be out of stock for this model? Thank you

Some are being added weekly but they sell out quickly.  Do you want to be added to the waiting list?

I have a 2020 Toolcat and would like to run a 72' Skid Pro snowblower model SP-01-1501. Toolcat has the standard 7 pin connector.

Did you order the snowblower with a 14 pin standard connection or their 7 pin tralier connector?

I have a Bobcat s250 and just purchased a Lorenz Snow blower, I am needing a harness to run the chute for the left/right function, is this the right harness or do i need another option?

Sorry but we have no way of controlling two systems from a Bobcat.

Do you know when you will have this item, or any 7pin to 14 pin controllers back in stock? Thanks, Mark

As soon as they show up.

I need a one function switch. SG-CB-1000A-100 is what I have been using and has been working well. I don't need 50 of them. Quantities of 10 has been my past orders. What is currently available in one or several quantities to keep me going.

We are best to send you to one of our OEM's then as we reserved the parts for the other controllers.  Most of them will be switching to 2000's once they run out.

When will this be available

Some are added to the site weekly but they sell out instantly.  It's taking us longer to recover from a 2 year parts shortage because there is such a huge demand.

Is this American funds

Yes.  We are an American company owned by a Candian and an Aussie.

I HAVE A BOBCAT T300 SKITSTEER THAT A CUSTOMER IS TRYING TO PUT A CAT PR172 ON. I ONLY HAVE TWO MOMENTARY SOLENOIDS TO OPERATE FOR LEFT AND RIGHT. IS IT POWIBLE TO GET THIS PROGRAMMED TO WORK WITH THE LEFT/RIGHT SWITCH ON THE LEFT STICK AND HOW LONG TILL THESE ARE BACK IN STOCK?

Sorry, but we don't do custom programming for 1 item.  900 are currently being made.  They will make their way onto the website in the next couple of weeks.  If you want more controls on the left stick you can purchase a 6014 which has 4 controls on the left stick.

SG-CB-2000A-100 When are you expecting this adaptor to become available?

There are 900 currently in the finishing process but the demand is high so as soon as they hit the site, they sell out.

What's the amp rating on these connections? Looking to run an agricultural pump for fire suppression and forestry spraying on a T590

8 amps.  Not meant for running pumps except for small chemical sprayers.  You can drive a relay and connect the other end to a battery if you need high amperage.

Hi i have a 2017 bobcat t595 7 pin i want to use a kabota 4-way dozer blade on it what do you recomend T

This controller will work well for that application.

I have a T650 bobcat and recently purchased a used erskine post pounder. It appears to have one 2-wire Delphi connector to run the left-right tilt function. What do I need to control it?

Just the 2000 controller.  You can cut off their connector and use one of the connectors supplied in our kit to change it to a Deutsch.

i have a wolvrine sickle arm mower how do i make it work on a 16 model t590 bobcat it has a 3 prone solinode on the mower

I have a real problem supporting that product since it is a direct Chinese copy of my product that I designed 20 years ago.  A 2000 controller will work but you will have to figure out the rest as I looked at it at an RB auction and could see it won't last long.

CLICK HERE FOR MY WARNING

Hi, I have a bobcat A300 with 7 pin output. I have 2 pieces of equipment that I want to run 1: backhoe,that has 1 solenoid and 2: a Harley rake that has 2 solenoids - could I buy the cb2000 and run both? Do you ship to australia?

Correct.  Yes we ship to Aus.  Use Fedex because Aus Post sucks.  They delay our shipments all of the time.

Do you ship to australia

Yes, but it's expensive.  It's best to use Fedex because Aus Post loses stuff and takes forever.

I bought your unit to convert 3 pin John Deere to 7 pin Bobcat. Soil conditioner will spin but it will not angle. Help asap

Just to be clear.  You have a John Deere/Paladin Harley rake and you want it to operate on a Bobcat?  If so the drum must be spinning in the locked on position.  You then use B2 or C2 to angle it while the drum is spinning.  Is this what you are doing?

I HAVE A 2005 T90 BOBCAT 7 pin and have 2022 TOPCAT Tree Shear model # ECSSRB that has a 7pin harness but not the same size. Do you have an adapter for this?

No.  You have to either chop off the connector and install a 14 pin or change out the harness altogether.   For the machine, you need a 6014.  Hurry as we are down to our last few and we have been waiting for 2 years for parts with no end in sight.

I have a 324g john deere, will this work for my ffc snowblower? Has 2 electronic hook ups but they need to be able to reverse current

This product is not related to your question in any way.  Please do not buy this item for your application.  We have a new product which will be available soon for your application but it is not ready yet.  Send us your contact information and we will contact you when they are ready to ship.

I have an 84” harley rake that I used with a case TR270 using a 14 pin connector. I now have a bobcat T66 with a 7 pin. This is a 2 coil single stem valve attachment. I just want to make sure I am in fact ordering the right part. Thanks!

This will work but you have to modify the attachment connection.

This item is plug and play.  CLICK HERE

hello would this work on my volvo mc 115c its for a lazer box blade form bobcat giveme acall at 575-642-4952

No it will not.  This is backwards to what you want.  This is designed to plug into a Bobcat machine.

For a box blade, you will need to convert it.  We can sell you the harness but you will need to work with a laser delaer to figure out the rest because they are all different.

I have a 2009 bobcat T190 with a 7 pin. I need to mate it to an older erskine model 1812 snowblower attachment that has a 4-pin connector. What product will I need for that?

Can you send photos of the connections and the actuators.

I’m trying to connect my bobcat to an old 4 pin Erskine snowblower attachment that runs the shoot portion from my joystick. Is this the product I need in order to do that?

Send us photos of the snow blower and connections.  I need to see what you are looking at.

I have a T590 with a 7 pin, I’m installing an FFC blower that has a electric rotation chute and an electric tip on the chute. Will your SG-CB-2000A-100 work for me? Thanks

No.  This must be an old blower because the new ones use electric over hydraulic controls.  For the older models, we have the following product available.

CLICK HERE

CLICK HERE FOR SETUP VIDEO

I have a bobcat t650 with the 7 pin connector but i bought a grouser 6 way dozer blade that someone cut the plug off of so i only have two wires now so i need a 7 pin connector with a controller on it i think so i can control the functions threw the two joysticks, will this work for that?

Yes this will work.

Can this be programmed to make the switches all momentary? I want to run a Metal Pless blade wings and not have latching on. Will I need to get the 6 function one with the 14pin output to do what I need?

The top latches while the bottom is momentary.  There is no way to change that.  The 6014 allows you to program what you want.

I Have a 2 function Tree shear Will this 2000 model make it work on my Bobcat with a 7 pin

Yes.

Do y’all make this with one 12v output? I found it listed on skid steer solutions but not here

That's what this is for.  CAN input and 12 volt output when you push a switch.