SG-CB-2000X-100 - Genius - 7 Pin Controller For Bobcat® Loaders - 2 Port | Skid Steer Genius
This adapter is specially designed to plug into any Bobcat® 7 Pin connector and allow the operator to run up to 2 x 12 volt solenoids directly from the left and right paddle controls of your Bobcat®. Works on Bobcat® skid steer loaders as well as Toolcat® and Versahandler® machines.
What is amazing about this is that we have taken our engineering to another level. This controller features a unique latching circuit so that you do not have to hold your thumb down for 8 hours for continuous operation.
It works like this: Plug in our controller and your switching paddles will be transformed. On your left paddle, touch the bottom part of the paddle and it works in a momentary fashion. Touch the top and it latches. Touch either the top or bottom and it releases. The same goes for the right paddle. Amazing, right? This was all done because of feedback from customers like you. Now you can run accessories like sprayers, lighting and accumulators without holding your thumb down for hour after hour while trying to run your machine. Genius, pure Genius!!!
Toolcat and Versahandler owners: Plug it in the same way as on a skidsteer and use the console switchs (Olders Models) or the handle control switches to operate your attachments. It's that easy.
Takes about 1 minutes to install. Is 100% plug and play. This configuration is a plug mount so you can use it over and over on any attachment that has one or two solenoids to control. This is complete and ready for plug and play directly into any Bobcat® branded machine. It has an indicator LED to show you that you have power and that it is receiving commands from the Bobcat® machine as well as when the paddles are operating correctly.
What is included:
- CanBus Controller with 2 outputs via a 4 pin Deutsch DT06 receptacle. Up for latching or down momentarily control from your left stick for port A. Up for latching or down momentarily control from your right stick for port B.
- 1 x 4 Pin DT06 Deutsch connector with an 18" pigtail to connect to your attachment solenoids from the controller.
- Easy to Follow Instructions
- Incredible factory support that is not available anywhere but from Genius.
Read more about how this product functions here.
This is not just a plug in adapter. There is a microprocessor with software loaded along with a IC driver circuit that enables this to work. That is why it costs more than just a plain old connector.
This is not a Bobcat® product. This product is not endorsed by Bobcat®. We are in no way attempting to make you think this is a Bobcat® product. This product is optically isolated from the controls of your machine and can in no way damage your machine or controls. It is perfectly safe to use and will not damage a thing. If a dealer is attempting to tell you that your warranty will be voided if you use this product or that it will damage your machine, please call and report it to us. Skid Steer Genius is a specialty controls company. Our goal is to make anything you buy for your machine work on any machine. Others design and build in such a way as to stop you from doing this.
Bobcat®, the Bobcat logo and the colors of the Bobcat machine are registered trademarks of Bobcat Company in the United States and various other countries.
Bobcat Company is a subsidiary of Doosan Infracore Bobcat Holdings Co., Ltd., a wholly owned subsidiary of Doosan Infracore Co., Ltd.
All rights reserved.
We Also Recommend
SG-CB-2000X-100 - 100 Pack - Genius - 7 Pin Controller For Bobcat® Loaders - 2 Port | Skid Steer Genius
SG-CB-1000-100 - 100 Pack, 7 Pin Controller For Bobcat® Loaders - 1 Port | Skid Steer Genius
SG-CB-2000X-100 - 50 Pack - Genius - 7 Pin Controller For Bobcat® Loaders - 2 Port | Skid Steer Genius
SG-CB-4014 - 50 Pack - Genius 7 Pin (4 Output) Controller For Bobcat® Loaders, Toolcat & Versahandler - 4 Port | Skid Steer Genius
QUESTIONS & ANSWERSAsk a Question
SG-CB-2000X-100 - Genius - 7 Pin Controller on a 2009 t300 g series with horst snow wing I bought last fall for local dealer. I have continuity through the cable to the solenoid, one wing works so i have power from the loader. checked 7 pin controller one side has power no power on the other side. wonder if his is fixable or do I need to replace or is it warranty. Now it's turning off the auxiliary hydraulics randomly. I have a bobcat dozer blade 7 pin that is working fine. Thanks Dan
Any chance that your machine is equipped with a 14 pin connector as well? If the Bobcat controller is installed in the machine as well, the Bus will see a conflict and shut off the hydraulics, beep and send an ACD code.
I have a Bobcat T190 that has a 7 pin Plug on it. I purchased a Virnig Power Rake that has a 14 pin plug on it on it. What is the easiest, cheapest way to convert it over.
An SG-CB-4014 is what is used.
what is the lead time on this adapter?
Order by noon and it ships the same day.
good morning, customer has used this adapter for only one season and has pulled apart, think do to being too short, is there a longer version of the same adapter?
No. If we made them longer they get caught and really torn apart. We make a box version with a long cable that can be mounted in the attachment. They can still tear the cable apart but it is replaceable. Here is is here. https://www.skidsteergenius.com/collections/7-pin-controllers/products/sg-cb-4000-108k-genius-7-pin-controller-for-bobcat-loaders-toolcat-versahandler-4-port-skid-steer-genius
I have a 2012 bobcat s 650 with a 7 pin and bought a Artsway 864 bale processor. Is the SG-CB-2000X-100 the right adapter for this unit. It is a 2 solenoid because the apron chain runs in forward and reverse. Let me know
Yes. This is a 2 solenoid product meant to select up to two solenoids.