Cart 0

SG-CB-1000-CTD - Bobcat® 7 Pin - Caterpillar Dozer Kit | Skid Steer Genius

  • $625.00

Ask a Question

So many people have asked for this that we decided to kit it to make it easier for you to choose.  This adapter is specially designed to plug into any Bobcat® 7 Pin connector and allow the operator to run up to 1 x 12 volt solenoid directly from the stick controls of your Bobcat®.  Works on Bobcat® skid steer loaders as well as Toolcat® and Versahandler® machines.  

Your Caterpillar dozer blade has 2 solenoids that operate in parallel top each other so here is what you do.

  1. Unplug your existing 8 pin harness.
  2. Plug in the genius Y-Adaptor
  3. Plug in the Genius extension harness.
  4. Plug the Genius extension harness into our CB-1000 controller.
  5. Plug the Genius CB-1000 into your Bobcat 7 pin.
  6. Swap the hydraulic couplers on your hose ends because Bobcat pressure is female where Caterpillar is male.
  7. Enjoy full joystick operation of your Ceterpillar Dozer blade on your Bobcat.

Takes about 1 minutes to install.  Is 100% plug and play.  This configuration is for plug mount so you can use it over and over on any attachment that has one solenoid to control.  This is complete and ready for plug and play directly into any Bobcat® branded machine.  It has an indicator LED to show you that you have power and that it is receiving commands from the Bobcat® machine.

What is included:

  • CanBus Controller with 1 output.  Up or down control from your left stick. SG-CB-1000
  • 1 x 2 Pin Deutsch connector to connect to your attachment solenoids from the controller. SG-DT06-2S
  • 1 x Y-Adapter to plug into each solenoid and into the extension harness. SG-Y-DT
  • 1 x 108" wire extension plugs from the Y to the CB-1000 controller. SG-DT-DT-108
  • Easy to Follow Instructions
  • Incredible factory support that is not available anywhere but from Genius.

Read more about how this product functions here.

This is not just a plug in adapter.  There is a microprocessor with software loaded along with an IC driver circuit that enables this to work.  That is why it costs more than just a plain old connector.


This is not a Bobcat® product.  This product is not endorsed by Bobcat®.  We are in no way attempting to make you think this is a Bobcat® product. This product is optically isolated from the controls of your machine and can in no way damage your machine or controls.  It is perfectly safe to use and will not damage a thing.  If a dealer is attempting to tell you that your warranty will be voided if you use this product or that it will damage your machine, please call and report it to us.  Skid Steer Genius is a specialty controls company.  Our goal is to make anything you buy for your machine work on any machine.  Others design and build in such a way as to stop you from doing this.  

Bobcat®, the Bobcat logo and the colors of the Bobcat machine are registered trademarks of Bobcat Company in the United States and various other countries.
Bobcat Company is a subsidiary of Doosan Infracore Bobcat Holdings Co., Ltd., a wholly owned subsidiary of Doosan Infracore Co., Ltd.

All rights reserved.

We Also Recommend


Ask a Question
  • I have a S650 Bobcat and I am trying to find a harness to fit a Quick Attach dozer blade. Serial #1025402. Will this fit?

    I would need to see which connector they are using.  Can you send a photo?

  • I have a 2020 bobcat t595 skid steer and just purchased a cat 84" harley rake serial number is PRW00377 Model PR184. Iam needing a harness to run the rake. Which harness do I need?

    If it is a new Cat brand Landscape Rake it should have a 14 pin connector.


  • I need a harness for a six way dozer blade. my machine is a Cat 279 C it has a 8 pin

    I need to know the brand and model of the dozer blade.

  • My t650 bobcat doesn't have an electric wire yet to the front of the machine. It does have multiple hydraulic lines for attachments. I am getting a caterpillar 6 way dozer blade tomorrow to use on my skidsteer. What is the most cost effective wiring setup to put on my skidsteer moving forward. I understand that I will have to get an adapter to go from the skidsteer to the dozer blade. Thanks In advance

    Buy the 7 pin control from Bobcat.


  • Customer has T66 bobcat with 7-pin and wants to operate a catepillar 14-pin attachment. Only 6 of the 14 pins are utilized on the catepillar. Is there a harness that will allow him to operate the catepillar attachment on the bobcat?

    I need to know which attachment.

  • Will this adapter kit work to convert a Harley rake mx7 soil conditioner as well? It only needs the electronic control to angle left and right. Thank you

    No it will not.  Left and right = 2 functions.  This is a single function controller.  You need at least a 2000 controller but anything bigger will work as well.

  • My bobcat. T76 2020 7- PINS connecting to can hookup Cat 6- way dozer blade model 231-5275 SN PRSSDB001286? If right one kits pls me let know thanks.

    Yes.  This is the correct kit.

  • i have a new john deere skid steer trying to hookup a bobcat sweeper and hammer attachments

    A hammer does not need electrical.  Just swap the couplers so the flow is going in the right direction.  The sweeper needs a harness.  Move the Ground pin in the machine and save yourself a lot of time and money in the future.  Here is a link to the harness needed for the sweeper and a link for pin moving instructions.

  • I have a T596 bobcat trying to hookup sweepster angle broom made by paladin will this wort

    I doubt it.  The angle brooms have two solenoids where this will only control one.  Without knowing the connector on the broom, I would have to guess so I will give you links to the units that I know will work and you can decide on the connector, if any.

  • I have a 2003 CAT 216 SKID STEER, 50 hp. There is no any pin connector on the machine at all. I want a wire harness which can be installed on this cat 216 to take a KUBOTA 76 Standard flow snow blower. Which harness I should buy from you? Please advise.

    We don't really do machine controls, but we do make controllers.  Here are a few options.  Please click the links.

  • tom from tmc excavating i have a wolverine cement mixer with 2 wire would the sd-cb-1000 ctd7pin work on my 590 bob cat

    You can use this.

    and this

  • bobcat T740 s/n B3ca17359 cat dozer 8 pin connector s/n231-5275 or PRSSDB000338 Will this work?

    Yes.  This is the correct item.

  • I have a CAT SR318 snow blower, will this allow me to run it on a Bobcat Toolcat 5610 with a 7 pin harness?

    No it will not.  This is a single output controller kit for a Cat Dozer.  A snow blower requires 4 outputs.  This is what you need.

  • I have a 6 way cat blade and it just plugs into one controller that come with the blade to make the tilt work then you run other plug to the battery but I have to swivel the blade all the way to one side with with constant pressure for my tilt to work from my switch will this fix that the bobcat is a t770

    The Cat blades have a dual port solenoid valve that bypasses flow to tilt when no power is applied. With your right stick momentary hydraulic control you can tilt it left and right. By applying power you will bypass the main flow and divert the flow to the secondary function. You will still need to use the same hydraulic toggle while holding the other button to then actuate the angling function. This controller kit works perfect for this application.

  • I have an Erskine broom with two solenoids setup to run on a cat skid steer 14 pin, do you have a harness to convert this broom to a bobcat 7 pin configuration? thank you.

    Yes. Please use the following product. It will plug into your Bobcat 7 pin and decode the controls as you operate the buttons. It will provide up to 4 outputs and can be used on multiple attachments with up to four solenoids. Here is the item. SG-CB-4014

  • Have a Cat 6 way dozer blade 231-5275 and need it to work on a Bobcat T770


  • I have bobcat t76, will this allow me to operate a cat bb121 box blade attachment?

    Yes, however you may need to move a couple of sockets on the attachment side.  Move A to G and J to H if they are installed.  A tool is provided and instruction videos can be found HERE

  • Hi, I read Q&A #4 about the bobcat T650 to a Cat 6 ways dozer blade and I am not I understand the answer. I have a 2017 Bobcat T650 with 7 pin control. I plan to buy a second hand Cat 6 ways dozer blade model 231-5277. 6 ways means 3 solenoids but this kit has only 1 output. How does that work? Would a SG-CB-4008 be more appropriate? Also, if I like to spend a little more money and plan for more flexibility in the future (e.g. universal 14 pins) what would you recommend? thank you for your help.

    6 way is kind of a mis-nomer in this case.  The pitch is handled by moving your machine quick change forward and back.  The angle is handled by your primary hydraulic controls which gives you left and right.  Your tilt is handled by triggering the solenoids and using your hydraulic contol to tilt left and right.  That's what they call 6 way.  If it has an old 8 pin, I would just change it all out with this kit.  CLICK HERE

  • I have a new bobcat t66 7 pin and trying to hook up to a paladin atp84 dozer blade which has a 14pin connector. Will this work?

    No it will not.  It is for a Cat Dozer blade.  You can use this, but you willneed to chop off their trailer connector and use our pigtail.


  • Are you able to receive pictures I have my cat blade at home now I need you to look at what I have on the wiring.

    Sure.  Send directly to this email address.