Menu
Cart 0

SG-CB-6014 - Genius 7 Pin (6 Output) Controller For Bobcat® Loaders, Toolcat & Versahandler - 6 Port | Skid Steer Genius

  • $865.00

Ask a Question

This is a true Genius Controller designed for solenoid controls only.  Our customers spoke and we listened.  You asked us to create a 14 pin output connector style controller so you could plug 14 pin attachments directly to your Bobcat® machines without using a box control and we listened. 

Here it is.  The new 6014 controller.  It is a 6000 series, 6 output controller with a 14 pin connector pinned the old fashioned way.  Using the old Bobcat 14 pin layout which works with Takeuchi, Gehl, Kubota, Mustang, Case and Cat attachments up to 6 controls plugs K pin power.

Programming: This new controller will allow the user to program the momentary circuits to be latching if desired.  Because of over current issues with your machine, you can program one out of each switch group only to be latching. Once you set these settings, they will hold inside the controller and you will not have to set them each time you start your machine.  You will be able to change them at will for different attachments.

  • A1/A2 - Pin C/D one can latch while the other will remain momentary.  These two functions do not work on Toolcat, Versahandler and hand foot control machines.
  • B1/B2 - Pin E/F one can latch while the other will remain momentary.
  • C1/C2 - Pin G/H one can latch while the other will remain momentary.

Because of fuse and circuit limitations, any combination of 2 will work at the same time.  If you try to make three latch, the circuit will reset and you will have to reprogram the adapter.  This is so the

    This adapter is specially designed to plug into any Bobcat® 7 Pin connector and allow the operator to run up to 6 x 12 volt solenoids directly from the stick controls of your Bobcat®.  Works on Bobcat® skid steer loaders as well as Toolcat and Versahandler machines.  

    Takes about 1 minute to install.  Is 100% plug and play.  This configuration is for boom mount so you can use it over and over on any attachment that has up to 6 solenoids to control.  This is complete and ready for plug and play directly into any Bobcat® branded machine.  It has power, communication, and a port status indicator LED to show you that it is working and that it is receiving commands from the Bobcat® machine.

    Throw away the crappy control box that the manufacturers supply and switch over to true machine controls.

     

    Bobcat 2020+ Versahandler 923 - DOES NOT WORK WITH THIS MODEL BECAUSE IT DOES NOT HAVE AN ACD CONTROLLER.

    DOWNLOAD MANUAL BY CLICKING HERE

    2024 UPDATE: It's hard to believe that 8 years have passed since this controller was first designed.  We have now introduced an updated version that was designed from the ground up.  CLICK HERE if you would like to learn about this new controller.  We have also designed a controller with 12 output controls.  CLICK HERE to learn about it.

    Disclaimer: 

    This is not a Bobcat® product.  This product is not endorsed by Bobcat®.  We are in no way attempting to make you think this is a Bobcat® product. This product is optically isolated from the controls of your machine and can in no way damage your machine or controls.  It is perfectly safe to use and will not damage a thing.  If a dealer is attempting to tell you that your warranty will be voided if you use this product or that it will damage your machine, please call and report it to us.  Skid Steer Genius is a specialty controls company.  Our goal is to make anything you buy for your machine work on any machine.  Others design and build in such a way as to stop you from doing this.  

    Bobcat®, the Bobcat logo and the colors of the Bobcat machine are registered trademarks of Bobcat Company in the United States and various other countries.
    Bobcat Company is a subsidiary of Doosan Infracore Bobcat Holdings Co., Ltd., a wholly owned subsidiary of Doosan Infracore Co., Ltd.

    All rights reserved.


    We Also Recommend

    Customer Reviews

    Based on 15 reviews Write a review

    QUESTIONS & ANSWERS

    Ask a Question
    • I have an older bobcat/IR 84" angle broom SN: 055000387 with a 14 pin connector. I just purchased a brand new 2022 Toolcat that has the 7 pin connector. Will this work?

      Yes.  It will work.

    • I have a Bobcat T590 with 7 pin. I need to run a 14 pin john deere attachment. Looks like this would work!?? Also, can I use the same adapter to run a Bobcat 14 pin attachment

      Yes, it will work but you must move the ground pin on the attachment from A to B.

    • I have a 2016 Takeuchi TL12 and I have a chance to purchase a Bobcat SG18 stump grinder. What will I need from you for it to work on my machine?

      CLICK HERE FOR THE INSTRUCTIONS


      Your machine must be equipped with 6 controls for this to work.  Contact us if you do not have enough.  We have a new product coming out soon.

    • Hi will the SG-CB-6014 work with a bobcat S590 sn:AR9R13577 and a Blizzard snowplow model Blizzard 810PP SS Thanks

      How many controls do you need?

      What kind of connector is on the plow?

    • Bobcat t870 to landpride 14 pin angle broom? Is it in stock?

      Yes.  In stock.

    • I have a 2012 bobcat t650 and want to run a cat hm115c mulcher. will this wok or that?

      Yes but you must push Pin K out of the attachment connector because it is a ground and will short out the 6014.

    • I have a bobcat t770 and I want to run and control a CAT stump grinder sg18b. What connector will work and is it plug and play?

      This is correct.  Make sure the connector on the attachment does not have Pin K installed.

    • Will this work on my bobcat T650. It has the 7 pin harness but I want to run a Harley rake that is a 14 pin. Bobcat is a 2011. Serial number A3P013141. Thanks! Also is there a phone number I can call for anymore questions I may have?

      Yes this will work.

    • I have a Kubota 6 way 8’ blade. Will this adapter work on my 2020 and 2021 Bobcats T770?

      Yes it will.

    • Will this work on a paladin harley rake Mx-7 that has 14 pin to go to a 2019 bobcat t650 foot control machine.

      Correct.  It will work.

    • I have a 2007 Bobcat T300 with joystick hand controls and a factory 7-pin harness. I am looking to run an older Bobcat/Melroe 90” dozer blade that is a 14-pin harness. Is this what I need or what is the best and most cost efficient option?

      This is the correct adapter.

    • Is the CB-4014 / 4 output version no longer available?

      Correct.  There are limited parts so we can only build a few models this year.  We opted for the 6014 because it covers more customers and runs more controls so there are fewer wiring issues.

    • Does this work on a 2018 JCB 3TS 8W Teleboom Skidsteer

      BOBCAT ONLY!

      Genius 7 Pin (6 Output) Controller For Bobcat® Loaders, Toolcat & Versahandler

    • color code chart CB 4014 14 pin

      Do you mean the internal wiring diagrams?  There is an input and an output.

    • We are a dealer installing an attachment on the customers t870 that has a 14 pin harness. The adapter you supply to convert it is 745.00/ is that retail? Is there a dealer price? we have a ND resale tax permit number of 74885. we are looking at buying two of them. Are they avialable to ship next week> Thanks Dave Prairie Implement & Equipment Inc

      1:  If you already have a machine with a 14 pin harness, you do NOT need our adapter.

      2:  Yes, that is the retail price.

      3:  Dealers need to email skidsteergeniussales@gmail.com with a resellers certificate and W9 and we can set you up in our system.

      4:  Yes, we have hundreds in stock.

    • I have a 2012 Toolcat and I purchased a Erskine Attachments snowblower with a 7 to 14 pin kit, recently, the blowers joystick controls have become intermittent or non functional. Will a 6014 control work with this attachment?

      If you have their 7-14 pin controller, then watch this as it teaches you about their fake SSG CAN controller and how we get calls like this all of the time because their controller either does not work or fails consistantly.  Our controller has been proven to work for over 12 years and thousands of units in the field.  Only if you physically have issues with your machine will it not work.

      CLICK HERE

    • I have a 2019 t770. I bought the pro plus grading blade. Is this what I need to run this attachment? Thank you

      Is that a Skeer?  What plug is on it?

    • I have a Bobcat T595 7-pin and want to run a KwikWay v-plow 14pin w/2 Solenoids. Is this the correct Adapter?

      Yes, this will work.

    • I am looking for a 7 to 14 pin adapter with 6 outputs wondering if they made such a thing

      You have the correct item selected.  6014.

    • Wool this work on a 2021 Bobcat T66? And what switch in the machine makes the 5th and 6th function?

      CLICK HERE FOR INSTRUCTIONS


      Many more valuable instructions can be found in our FAQ section as well as our video catalog.

    • 1991 bobcat 753 Have a bobcat v-blade snow plow, with 7 pin electric controller. Need the extra joystick and plug to control the functions.

      The 753 won't have 7 pin control.  The only simple way of doing this would be the following items.  Are you sure that the machine has enough hydraulic flow to operate this blower?

      CLICK HERE FOR THE HARNESS

      CLICK HERE FOR THE CONTROLLER

    • Will the SG-CB-6014, run a Road hog planer with 14 pin harness on a Bobcat with 7pin harness? The roadhog has 6 coils on this attachment that move 3 cylinders both directions. The photo of your 6014 only shows 6 pins being used on the 14pin connector. I would have thought we would need at least 7 pins to control 6 different coils. Please let me know.

      Yes it will work.  There are 6 control pins and one keyed 12 volt pin plus ground.  The sample I had for the photo was ugly so I used the 4 channel for photos.  It is the same box and cabling.  Just more controls.

    • will this work with a halverson 120 woodprocesser to a 2019 t-630 bobcat thanks

      Yes but please read the Halverson FAQ so you have instructions.

    • Does this controller come with the magnetic mounts for the boom?

      No because it is a lot smaller and can be zip tied to the hoses now.

    • I want to run a Cat PC306 Cold Planer (14-pin) on a Bobcat S650 (7-pin). Will SG-CB-6014 work, or is there a harness adapter you can supply?

      The 6014 is correct.  On the planer you will need to remove Pin K and move Pin A to G and J to H.

    • I am trying to get controls to work on a s66 with a john deere cp24e not Wirtgen cold planer cant get any thing but the drum to work

      Do you have our controller installed?  Did you swap the hydraulic couplers so the forward flow is moving the drum in the correct direction?  Are you aware that you need to push two button controls at the same time to get it to work?  One button for direction and one button for selection.

    • All functions working except the drum pitch/tilt forward and backward. Is there something we are missing?

      Can you tell me what you are talking about?  Stump Grinder, Planer, Mower, mixer?  Brand? Model?  Did you order anything from us?  Order number?  There is no way that I could even begin to guess what this is.

    • t s66 to john deere cp24g

      That controller will work but you will need to move the ground pin in the attachment from A to B. 

    • Good Morning Is this the unit I need to run my Halverson wood processor if I have a 7 pin receptacle on a bobcat S770

      Yes. CLICK HERE for instructions.

    • I have a 2019 toolcat with 7 pin trying to hook up to a 14 pin tree saw only 3 solenoids to control will this work for me?

      Yes. This will work.

    • Good Morning, I am trying to use a CB-6014 controller to run on a T770 with a 7 pin to a CAT PC306 or a SW345 Wheel Saw. I saw in the Questions and answers section you said you remove K.(Done) and the put Pin A into Pin G and Pin J into Pin H. When I received my controller. There was nothing in A or J. However, pins already in G and H. Do I need to do anything different to run these two attachments?

      These instructions are for the attachment side. Move A to G and J to H so it aligns with our controller. Push G back into the connector because it is a ground and our controller puts out +12volts so it will blow your fuse.

      #1 thing to do is to swap the hydraulic couplers because Bobcat is backwards to Cat so you will never get High FLow out of the couplers. You must be able to use the right trigger to spin the drum in the forward direction.

      Does the PC306 have pins in L & M? If so it could be a SMART attachment which uses CAN to operate. We are currently working on a solution but do not have a breakthrough.

    • I ordered a SG-CB-6014 and was thinking that it would have programmable controls to keep a switch on or be momentary if I wanted?

      Yes it is programmable. Here are the instructions.

      Skid Steer Genius - Latching Feature as added to Production SG-CB-6014 - 6 AUG 2021

      As shipped to customers the latching feature is not enabled. Users can enable this feature.
      Each time the machine is turned on the status LED will be steady Green for several seconds.
      During this period outputs to solenoid valves are disabled and latching can be enabled or disabled. Then the green light begins flashing green on each new data packet received from the machine.

      Using the Latch Feature
      Pressing the B1 button will always turn on the appropriate output
      Holding the B1 button down for more than about 6 seconds will latch the output on continuously Pressing the B1 button again will reset the latch and turn off the output.

      Operation using the A1, B1 and C1 button is identical.

      Enabling the Latch Feature
      Latching is available only on the A1 B1 and C1 buttons

      A1 Left toggle moved to left
      B1 Inner button up on left stick C1 Inner button up on right stick

      A2 Left toggle moved to right
      B2 Inner button down on left stick C2 Inner button down on right stick

      To Enable the A1 Button Latch
      Push and hold the A1 button at power up (during the several second period with green status)

      When the latch enable request is recognized, the status LED will turn RED
      Hold the button down until the LED changes to steady Green. Turn off machine for 10 seconds

      To Disable the A1 Button Latch
      Push and hold the A2 button at power up (during the several second period with green status)

      When the latch disable request is recognized, the status LED will turn RED
      Hold the button down until the LED changes to steady Green. Turn off machine for 10 seconds

      To Enable the B1 Button Latch
      Push and hold the B1 button at power up (during the several second period with green status)

      When the latch enable request is recognized, the status LED will turn RED
      Hold the button down until the LED changes to steady Green. Turn off machine for 10 seconds

      To Disable the B1 Button Latch
      Push and hold the B2 button at power up (during the several second period with green status)

      When the latch disable request is recognized, the status LED will turn RED
      Hold the button down until the LED changes to steady Green. Turn off machine for 10 seconds

      To Enable the C1 Button Latch
      Push and hold the C1 button at power up (during the several second period with green status)

      When the latch enable request is recognized, the status LED will turn RED
      Hold the button down until the LED changes to steady Green. Turn off machine for 10 seconds

      To Disable the C1 Button Latch
      Push and hold the C2 button at power up (during the several second period with green status)

      When the latch disable request is recognized, the status LED will turn RED
      Hold the button down until the LED changes to steady Green. Turn off machine for 10 seconds

    • Will work with CAT PC 306B grinder asphalt with 7 pin bobcat t76?

      YES, but planer pins need to be moved.

      Move A to G and J to H. If there is a pin K push it back inside the connector and do not use. It is a graound where Bobcat uses it as a +12 output so it will blow your fuse.

    • Do you have an ETA on when these will be back in stock?

      100 are currently being loaded at the warehouse.

    • Looking for SG-CB-6014 - GENIUS 7 PIN (6 OUTPUT) CONTROLLER FOR BOBCAT® LOADERS, TOOLCAT & VERSAHANDLER - 6 PORT | SKID STEER GENIUS - what is the current price and availability?

      100 are currently being received into stock.

    • When will these be available?

      100 are currently being received into our warehouse.

    • Could somebody email or call me when one of these is available to purchase? We were told "maybe" they would be by now, but apparently they aren't available yet. I need this to run an Artsway Bale Processor to spread mulch on a job that has a deadline. If this part isn't available, I'm going to go a different route altogether; I need a definitive answer for availability otherwise we're forced to find an alternative piece of equipment. My number is seven 1 two - five 48- three five three zero. Thank you.

      In stock now.

    • I have a brand new Bobcat T650 foot control only. Will this work to connect 14 pin attachments?

      This works on all current models produced in the USA. Two of the channels do not work if your machine was made in the Czech Republic. The new CAN60 will work on all models. Yes. I connects to 14 pin attachments.

    • I have a bobcat 6 way dozer blade from 2016 with a 7 pin male plug. Just bought a ‘24 Kubota 75-3 and need to plug it into the Kubota 14 pin, this doesn’t look like it’ll work…

      No it will not. It says that it is a controller for Bobcat loaders. You have a Kubota loader.

      CLICK HERE

      For Bobcat Dozer instructions and ordering information. Most questions and answers can be quickly found in our FAQ section by CLICKING HERE and/or our Video Section by CLICKING HERE.

    • I want to route a 14 pin harness with the 7 pin and "T" into the connection in the back of my machine. do you have an adapter for that?

      That's a Bobcat question. There are different harnesses for different models and serial numbers of machines. You will need to call a dealer with your serial number ready.

    • Will this SG-CB-6014 output to both Bobcat and Caterpillar 14 pin connectors or do I still need a 14 pin Bobcat to 14 Pin Caterpillar D series adapter to go between them?

      Depends on the attachment. The first 4 outputs are the same on both. If you need the 5th and 6th, then you need to move the sockets in the attachment. Move A to G and J to H. Make sure that the HF sense is pushed back into the connector on the attachment side (Pin K) this is a ground and will blow your fuse immediately. It is not needed to operate a Cat attachment on a Bobcat.

    • Will this SG-CB-6014 - GENIUS 7 PIN (6 OUTPUT) CONTROLLER FOR BOBCAT let my T650 with 7pin run a bobcat 84" soil conditioner plug and play ?

      Most Bobcat branded soil conditioners are 7 pin CAN controlled. Only a really old one should have a 14 pin harness attached. If you have a 14 pin, then yes, this will work. More in stock next week.

    • When will this item be in stock

      In 1 - 2 weeks.

    • Need the wire color to alpha pin location for the fourteen pin end of SG-CB-6014 (?). Controller has 8 wires going to the 14pin connector.

      6014 Colored Pin-out

      14 Pin - Wire Color
      B - Black
      C - Orange/Black
      D - Orange
      E - Green
      F - Blue
      G - Red/Black
      H - Red
      K - White

    • Hey Craig, the SG-CB-6014 you suggested I buy is sold out. I can't order it. When will it be available? Thank you

      Soon. We have stock arriving weekly. A second supplier is coming online soon to help us catch up.

    • How soon will these be back in stock??

      Some arrive weekly.

    • SG-CB-6014 adaptor; Are these excepted in stock soon?

      Yes. Two sources coming on deck soon. Some are still trickling out of the old vendor. Send us your details and we will alert you when more are added.

    • When will the SG- CB-6014 controller be available.

      Trying to keep them in stock but they keep selling out.  A second supplier come online in a month.  Hopefully some will trickle in before then from supplier 1.

    • SG-CB-6014, When can I buy 1. Says out of stock

      A whole bunch on the way.  They just keep selling out.  A second supplier will be online in a month to help us catch up.

    • When will more be available in stock?

      Any day

    • Can you email me when these are back in stock?

      Yes.

    • when will these be back in stock?

      NOW.

    • Good morning, What's the availability of this item: SG-CB-6014? I would like to place an order for one. Thank you,

      They are in stock now but selling fast.

    • Please let me know when SG-CB-6014 is back in stock.

      There are some now. They are selling fast.

    • Sold out in 20 minutes? Trying to purchase 20 minutes after I got the email

      In stock NOW.

    • Any idea when these will be available again

      There are some loaded now.

    • When will the SG-CB-6014 be back in stock? Thanks

      In stock now.  But they are selling every few minutes.

    • Looking to purchase the SG-CB-6014 adapter. It's out of stock, any idea when they will be available again? Also, Can I submit an order for it being out of stock and get shipped when it becomes available? If there is backorders would like to get in line asap.

      Yes. Send us your details and we will add you to the contact list.  Several hundred are supposed to drop any day.

    • When will these be back in stock

      Supposed to be months ago.  Our current supplier lies to us weekly and will be replaced soon.  Currently we have no answer because we would be passing on their lies.

    • When will these be available again?

      Hopefully soon.

    • When will these be in stock again. Need asap please

      Sorry but our supplier lies to us on a daily basis so we have no idea.  All I can say is to give us your information and we will add you to the contact list so that you can order one as soon as they arrive.


      I am working on replacing this supplier but it takes time to create a new supply chain for a custom product.

    • How long before this is in stock?

      Every week we are told one more week.  We were told last week for sure but this week we are told that they are still curing and will need to be final tested and then several hundred will be loaded.

    • When will this be back in stock?

      Any day.

    • I need to order this for when it’s available can you please let me purchase and put on ship when ready?

      Yes.  Reply to this with your contact information and you will be notified the night before we load them.

    • Will this work for the new R-Series Bobcat S86? Looking to run a Cat 14-pin planer (PC408B). When will you have more stock? Thank you,

      Yes it will work.  Expecting a ton of stock within a week.

    • can i use this harness to get 12v constant/key power to a laser controller on my grading attachment. i understand that i could use it to also get control of the valves by just tying into the current valve wiring.

      Yes, it has a pin K which provides key power.

    • Hi, You indicate in the notes that the SG-CB-4000A-100 will not fit 2020+ Bobcat 923. I am looking at ordering the new TL923 and I am wondering if this statement holds true to the new model too. If so, do you have another solution for me? Thank you for your time, Clarence

      These models use a 7 pin connector as an output but they do not use CAN language.  This is so confusing because people have bought controllers only to find out they did nit need controllers.  They just needed a mating connector.  Talk about confusing customers.  Your machine will allow up to four outputs using just 12 volts when you push a control button so that's it.  Easy Peasy!

    • Will this work to run an EDGE Snowblower Model # 50503890 with their 14 pin? Trying to install on a Bobcat Toolcat 5600. If so, when will they be available? Thank you!

      Yes it will work.  There are a few hundred about to be added to the site any day.

    • Hello, will this adapter be back in stock soon? Thank you!

      Any day now.  Send us your information and we will add you to the contact list when we add them.  We are adding a second supply chain in 2024 so these out of stock issues will end soon.

    • When will this harness be instock again?

      Any day.  Send us your information and we will contact you when we are loading them onto the site.

    • Dear all, we would be delighted if you could inform us if the controller SG-CB-6014 - GENIUS 7 PIN (6 OUTPUT) CONTROLLER FOR BOBCAT® is available for shipment to Italy or, if it can be delivered by the end of January. For further information please do not hesitate contacting us. Kind regards, Hannes

      If you provide your details, we will contact you when they are available.

    • Is it still possible to get one of these?

      In January there will be another batch.

    • Do you have an idea when you would have these back in stock?

      Any day.

    • Good evening guys. I reached out several months back about the control harness for a Toolcat. I believe I was added to a list when these become available and was wondering if we were coming up on the list yet?

      Pretty quick we are expecting a bunch of these.  You will be contacted when they come up in the next couple of weeks.

    • When will this be available?

      Any day now.

    • SG-CB-6014 - GENIUS 7 PIN (6 OUTPUT) CONTROLLER FOR BOBCAT® LOADERS, TOOLCAT & VERSAHANDLER - 6 PORT | SKID STEER GENIUS Is this still sold out? I am unable to add to cart.

      Soon

    • Shows out of stock. is this item discontinued? If it's still in production, how long until you can have one made and shipped?

      Expecting stock any day.  They sell out fast so send us your information and we will contact you immediately.

    • Hi from Germany - can you give an estimation when this controller comes back for purchase? Do you still need VND5050AJTR-E ?

      We redesigned them to take another chip and then it went into long deliveries.  We are getting them slowly in but they sell out immediately.  I am redesigning one more time to use chips not related to automotive at all and that should do it.

    • HAVE A 2014 T770 6 PIN AND WANT TO USE A CAT HM315C FORESTRY MULCHER WITH 14 IN. NEED? PLUG AND PLAY? ONLY RUNS THE DOOR ON THE MULCHER

      Bobcat uses 7 pin CAN controls.  Click here for the converter.

    • SG-CB-6014 I need to be on your waiting list for this product please

      Please respond to this with your email and phone number.

      Thank you

    • when will this cable be available ? It says that it is sold out. thanks arln

      We add some each week but they sell out immediately.  Send us your contact information and we will add you to the list for when we are about to load more into the system.

    • Will this work on a bobcat s770 to run a cat pc305 cold planner

      Yes, but make sure you understand the Cat instructions because you have to push two buttons at the same time to operate most functions.

    • have a ssg2524 stumpgrinder need to put it on a S650 Bobcat what do i need

      Yes. A 6014 will work.  We sell out within a couple of days of adding stock so you can send us your details and we will contact you as soon as we are adding more.

    • I have a CAT 262D3 14 Pin trying to use my bobcat 7 pin power hydraulic angle broom on will this adapter work?

      This is backwards.  It says for Bobcat loaders.  You have a CAT.

      CLICK HERE FOR THE INSTRUCTIONS FROM OUR FAQ PAGE

    • Can I order now, and have it shipped, when it comes in? This is to fit our 2023 Bobcat T770 T4, to a John Deere 6 way Dozer Blade , Model DB84. Ser. ITODB84XJM0000815

      Respond to this with a number and we can add you to the list.  They were being added to inventory yesterday so any time today they will be in stock.

    • I just purchased a new Cat SR121 Snowblower (14 pin) and would like to use it on my Bobcat Toolcat UW53 (7 Pin) Would this work?

      Yes, this is correct as long as the blower is not High Flow.  If it is, you must push pin k in the attachment plug through so it is not used.  On Cat it ia a ground.  On Bobcat it is +12volt so your fuse will blow instantly when connected.

    • HOW LONG WILL THIS PRODUCT BE OUT OF STOCK? WHEN IN STOCK, WHAT IS LEAD TIME FROM ORDERING TO SHIPPING?

      We get a few weekly.  We can add you to the waiting list if you respond.

    • When do expect to have the sg-cb -6014 connector

      A few arrive each week as we ramp up production.

    • SG-CB-6014- Do you have this part? Any ideas who might. Trying to convert from a 14 pin kubota to the bobcat

      They will be back in stock soon. They regularly sell out.

    • when do you expect to have these back in stock?

      Loading some each week but they instantly sell out.  Do you want to be added to the contact list?

    • Craig in Sales and Technical Service was very helpful - forwarding a link to the converter - asking that orders be placed online - however, it doesn't appear that the SG-CB-6014 - Genius 7 Pin (6 Output) Controller For Bobcat® Loaders, Toolcat & Versahandler - 6 Port | Skid Steer Genius - is available. Is there an anticipated date when the product will be available for sale?

      Loading more each week.  Just watch for the updates or get back to Craig and he will add you to the waiting list.

    • When will these be back in stock? Do you have a date

      Being loaded into the site this week.

    • Any idea when these are due to be available?

      There should be some being loaded next week.

    • Do you have an idea of when the 6014 controller will be available again?

      Any day now we will start loading the pipeline.  Send us your email and we will add you to the waiting list.

    • Check to see when these are expected to be back in stock?

      So are we.  It's getting ridiculous.

    • When will this part be back in stock?

      As soon as they get here. Respond with an email and we can add you to a list.

    • I have an Arts Way top spreader and it only has pins in the C, A, and G spots. When I attach the adapter, the conveyer still won't work. Is it because there is not a pin in the A spot on the adapter? If so, which pin do I move into the A spot?

      A is not a supported position. Only Cat uses A. There is a tool that is shipped with the controller so you can move a pin as needed.

    • I have an Arts Way Bale Processor (14 pin) to be used on a T770 7 pin Bobcat. How do I go about seeing if I need to move any pins around on either the 7 pin or 14 pin adapter. I've plugged it in and the hydraulic conveyer is still not working.

      DO NOT EVER TOUCH THE 7 PIN OR YOU CAN BLOW UP THE ECU IN YOUR MACHINE!!!

      CLICK HERE TO READ MORE

      Not sure what you plugged in but this sounds scary if you messed with the 7 pin.

      You need a controller that converts the Bobcat digital signal to 12 volts analog.

      CLICK HERE

      Respond back with your email and we can add you to the waiting list.

    • I have a 14 pin Arts Way bale processor to be used with a 7 pin skid steer. Do you have an adapter that will work for that and in stock?

      This is the correct item CLICK HERE

    • I would like to order this SG-CB-6014 but it will not let me add it to my cart as the button just says "sold out". What can I do to get on the list for you build me one of these?

      Watch the site.  We add some weekly as they come in but they sell out immediately.

    • How soon will SG-CB-6014 adapter be available?

      Was just sent another delay notice today so we have no idea.

    • Do you have an ETA on this yet? SG-CB-6014 I would like to order one as soon as I can. Thanks

      Some show up weekly and we add them but they sell immediatley.  We still have extreme parts shortages in our supply chain that we are working through so large runs are impossible.  We can only build a few at a time as parts appear.

    • Do you have inventory yet for Bobcat ?

      Working on it.

    • I have a Bobcat Skid steer (relatively new machine) that has a 7pin and I am trying to get a level best GB108 and PD84 to run on it (14 pin with automatic machine control). Will this product work for that application?

      If you ordered it with the 14 pin connector pinned for old Bobcat, it will work like this.

    • Do you know when stock levels will be replenished? I need to order

      There are some being added to the store each week.  Just keep watching.  We stopped allowing backorders because peoplemis-understood that for ship it yesterday.

    • Any Idea when this will be available?

      Every week we add some and they sell out.

    • Looking to buy one Is one available 2012 bobcat 7 pin to 14 pin

      Keep watching the site as we add more weekly.  They just seem to sell out faster than we can make them.

    • what day do you load the site for SG-CB-6014

      We never know when we have shipments.

    • when will there be more SG-CB-6014 available

      We load the site each week and they sell out immediately.

    • when will you have these units back in stock. Mine shorted out this morning and started smoking. we are a paving contractor in north Alabama and i rely on this skid steer.

      They are in each week but sell out quickly.  I really cannot explain why so many sell so quickly but we have added another production facility to produce these so hopefully soon we will get ahead of the curve.  If you place an order, you have the best cance of being in the next batch to hit the site.

    • I have a Bobcat T550 with 7-pin, looking to use your 14-pin to interface to connect to a variety of attachments having 12V solenoid valves. Do you provide pinout information about the 14-pin so I can ensure proper wiring to various attachments? When do you expect to build up another batch of these so I can order one?

      There are some added to the site each week but they sell out almost instantly.  It's going to take a while for us to get ahead.  The pin-outs for all of our controllers are shown HERE

    • Will this work with a 2023 Bobcat T-66 over to a 14 pin grader?

      It depends on the grader.  Brand and model please?  If it's an RB Auction Chinese special I will need photos of the solenoids as they are all different depending on which parts they are trying to dump in the USA.

      If it's Chinese, I will provide the controls but I will not troubleshoot the mechanical issues with the grader.

    • I have 2022 bobcat 770 and will need to run a cat cold planner milling attachment . Will this work ?

      If it is an older Cat planer, yes.  If it is a brand new Cat planer that uses SMART technology, no.  If it is a really old Cat planer with 5 hydraulic lines, kinda sorta.

      CLICK HERE FOR OUR FAQ

    • I have a 2000 Bobcat 763 with a 7-pin connector in the back of the machine. I just bought a Halverson firewood processor (HWP 120) and I need a 14-pin connector to run it. I've watched several of your videos and I've read most of your website -- I'm still a little confused on what I need to order. I'd like to run the cable to the front of the machine to where the hydraulic connections are but then I need to convert it from 7 to 14 pin and then map the buttons on my controls to the attachment.

      A 763 should have a 14 pin installed on it already.  Halverson provides a 14 pin connector with their processors.  Their schematic is usually wrong so I created this page to help people out.  CLICK HERE

    • I have a 2018 t770 hand foot controls and would like to run a grader blade with 6 solenoids. What controller gives me the six functions then?

      CLICK HERE FOR THE 6014 6 CHANNEL CONTROLLER

    • Will this work with 4 solenoid set up?

      It is a 6 output controller which means it will operate up to 6 solenoids.

    • I HAVE A BOBCAT S750 I am looking for a 7PIN to 14 pin adapter to run a new holland attachment will this work

      Yes it will work.

    • will this work on a hand and foot control bobcat as well as a joystick machine for a PC305 planer?

      Currently will not work on an S570/S590.

    • Just got a grader attachment but is wired for the 14 pin bobcat and i have a 2021 s66 the grader has a hydraulic cylinder on the left and right side to move the cutting edge up and down will this plug work for that

      Yes, it will give you 6 controls.  If you have a Bobcat grader, there should be a controller buried in there with a 7 pin harness.

    • I need to put a grader attachment on a 5600 tool cat with 8 solenoids, do you/can you make a controller with 8 outputs all momentary?

      A grader will not work well on a Toolcat as it has a front suspension that will jump up and down.  You won't be able to use your stcok controls and since you have a stearing wheel it would be too difficult to use any of our controllers.  If you insist, I would use a 6014 and an injector adapter.

      CLICK HERE FOR OUR 6014

      CLICK HERE FOR OUR INJECTOR

      You grader mush have a 14 pin harness installed for this to work.

    • I have a bobcat 753 and I installed the wire harness for the 7 pin connector. What should I use on this machine? 6/4 output controller? I have a Harley rake that I use, but also would like to just all that buttons if need be.

      The 7 pin controllers were not designed until years after the 753 went out of production.  Can you send me photos of your sticks and your 7 pin set-up as I have never seen this type of install.  A real Harley rake only needs 2 controls.  A snow blowers uses 4.  Only a cold planer would use 6 and your machine is too small to operate one.

    • Is this the right connector to use if i have a John deere 325G and want to run a bobcat brand soil conditioner with a 7 pin connector on it?

      NO.  Per the heading, this is to blug into a Bobcat skid steer.

      CLICK HERE FOR OUR FAQ

    • Any idea when these will be back in stock?

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • When will this harness SG-CB-6014 be available? Thank you.

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • Looking for 7 to 14 pin with 4 functions

      We may have a few trickling in over the next few weeks.  Keep watching the site.  They sell as fast as we list them.

    • Hi there had an little accident with this controler .pulled the wires out of both pluges.Would you be able to send me the wiring diagram for the 7 and 14 pin ends. Thank you

      Send us your email.

    • is this still sold out?

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • When are y’all gonna have SG-CB-6014 7-14 pin controller back in stock

      What attachment do you need to operate?

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • when will you be getting the SG-CB- 6014 controllers back in stock? can i still get one put on order? thanks

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • i have a2022 t64 bobcat and i need a 14 pin adapter to run my older attachments . stump grinder and snow blower and blade

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • Do you have a approximate lead time for when the sg-cb-6014 adapter will be back in stock? Or what a similar substitute would be?

      What attachment do you need to operate?

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • when are you expecting more to be available?

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • Need to make an angle broom and a sweeper broom both with 14 pin connectors work on our 2010 S185 which has a 7 pin connector. What is the best option? An adapter cable or to change the connector cables on the brooms? Please include what part numbers we need.

      Normally I would say to use a 6014 but we ran out today after waiting 2 years for parts.  This all all that we have now but we are about to run out of them as well.


      CLICK HERE

      Until we can buy one critical part, these products are shut down.

      Due to a worldwide shortage of IC's, we are in a crisis mode.  We have waited for 2 years for parts and still nothing in sight so we are redesigning the product to utilize relays until we can get drivers.  

      Here is what we need.  If anyone can help us source these, we would be forever greatful and will give you a unit for free.

      VND5050AJTR-E - I will take 25000 of them.

      So to answer your question, we really have no answer until we can get this part.  We have thousands of boards built but we need this critical part.

    • I have a 2021 Bobcat T770 with SJC and 7 pin connector. I am getting a Vail Products; Vail X series tree saw with herbicide and rotating cutting head.It has a Rotary Actuator-driven cutting head. Comes with a 14 pin connector standard. Will this unit work?

      Yes as long as it has a 14 pin that is set up to standard Bobcat.  B - Ground, CDEFGH for control.

    • I have a SB72 Edge snow blower. It’s bobcat 14 pin. My Toolcat 5600 and my T870 both have the 7 pin will this work? I need 4 functions for the Shute.

      That is the correct controller. for both.  Hurry as we are almost completely out and we have been waiting for parts for 2 years with no date in sight.

    • Are these available? What is the timeline if you don't have it available.

      We still have some.  When we run out, we may have a problem since parts have been on order for 2 years with no set date in site.

    • I have a 2012 Bobcat T650 with a 7 pin connection and need to adapt to a new Cat SR321 snow blower. Can you help and how fast can I get the adapter? Thank you!

      The 6014's are currently in stock.  Shipping speed depends on how much you want to spend.

    • I have a 2021 Jcb skid steep and I need to plug my bobcat cold planner into it but the bobcat cold planner has a 7 pin and my Jcb has a 14 pin. Will this adapter work?

      No this will not work. It is the opposite of what you need. 


      Click here for instructions

    • I have a 2022 T76 and want to put a snowblast snow blower on it that was on a gehl skid steer. Will this work?

      If the attachment comes equipped with a standard 14 pin connection, this is the correct controller.

    • We have a 2009 5600 tool cat will the SC-CB-6014 work for a Kubota SSG2524 Stump Grinder

      Yes.  Just kind of a hassle to use your controls since they are down by your right hip.

    • I have a 2022 bobcat t770 and a level best box blade. Will this work?

      Yes.

    • i just want to make sure this is a 7-14 pin connector

      Yes it is.

    • Hi, I purchased a multi function snow plow (Blizzard 810PP) converted from a truck plow to a skid steer plow. The guy I purchased it from had it working from a new SVL65 (constant flow hydraulics through the block, then Blade L-R, left wing In-Out, right wing In-Out. Sorry if this is redundant, I couldn't see the full answer below for some reason, just more questions I am trying to put that on a 09 Bobcat S250 (hand/foot) controls currently equipped with a 7-pin and did not fully understand how that Bobcat system worked. Looks like some of the adapters don't allow for 3 functions with hand and foot controls. Is there one that does allow for 3 functions with H/F controls? And secondly, do you know if the Bobcat brand conversion kit for the S250 would allow all 3?

      An S250 should work with all 6 functions.  Yes, the Bobcat converstion works as well but I have been told that they now cost $1500 and take 6 months to get.  Let me know if you have been quoted differently.

    • I see that there are some adapters that are no longer available, will this this work to run 14pin attachments on the 7pin Bobcats? I will need a couple are they in stock.

      Yes, this is the newest one.  Because of parts shortages, we had to pair down our offerings until things open up again.

    • I just bought the 6014 controller for my 2016 T770 Bobcat, and am trying to operate a bradco tiltach and johndeere 4-1 bucket, but I cant get the tilt tach to operate

      You must hold a control button to trigger our controller while you operate the right handle hydraulic control.

      PLEASE CLICK HERE AND WATCH THIS VIDEO
      CLICK AND WATCH THIS VIDEO AS WELL

    • Can i use my tax if number so I don’t have to pay taxes?

      Unless you are in Washington State, we do not charge tax.

    • I have a BobCat S740 (7 pin) and an Erskine 2118 snowblower ( 14 pin), will the SG-CB-6014 controller work for these?

      Yes.

    • What is the wiring diagram from the 4 wires from the 6014 controller to the plug that plugs into the bobcat, the wires got ripped out of the connector and I just need to reinstall the pins into the plug

      CLICK HERE FOR OUR FAQ

    • I have a 2020 Bobcat T870 with a 6014 trying to use a Caterpillar 2022 Harley Rake. The only controls working are the Hydraulic flow buttons on the Bobcat. It flashes green for the can bus and solid green for power. When I hit the controls the Harley rake doesn't respond but the controller turns red.

      This means the controller is working.  The rake should be spinning when you push the button.  Here are the rules:

      1:  Cat and Bobcat run their hydrualics in the opposite direction.  You must swp the couplers on the attachment hoses before yu try and operate it.

      2:  On your Bobcat right stick, you must push the trigger and lock the hydraulics on so the drum is spinning with your hands off the controls.

      3:  Push your control toggles.  It's usually the up down controls on the left and right stick.

      4:  If this still does not work, send us a photo of the attachment connector so we can see which pins they are using for control.

    • I have a 2019 toolcat with a CID angle broom (14 pin connector). Is this the correct adapter? The one that my dealer sold me has a round barrel like the SG-CB-4008 but the pin configuration looks like the SG-CB-60DP8. The adapter had a green flashing light that no longer turns on and I cannot angle the broom anymore. Thanks

      If the broom came with a 14 pin then this will work.

      If your adapter does not come on, have you checked the fuse?  They don't usually just dies unless they are physically damaged.

    • Bobcat s510 with 7 pin harness added after purchase going to a 6 pin trailer plug on a quick attach soil conditioner. What's the best way to get our stock joystick buttons to angle the attachment?

      CLICK HERE FOR THE ADAPTER