Bobcat 7 Pin to John Deere 3 Pin Controller
If you have a Bobcat loader with a 7 pin CAN controller and bought a John Deere attachment with a plastic 3 pin connector, then this is the kit for you.
This kit includes the 2 channel Bobcat controller and the output adapter that goes to the John Deere 3 pin plug. There are extra pigtails included for other attachments if needed.
This adapter is specially designed to plug into any Bobcat® 7 Pin connector and allow the operator to run up to 2 x 12 volt solenoids directly from the left and right paddle controls of your Bobcat®. Works on Bobcat® skid steer loaders as well as Toolcat® and Versahandler® machines. Additionally this comes with a 3 Pin plug to mate to John Deere Attachments. Now you can plug your John Deere Broom directly into your Bobcat® and it will work perfectly from the button controls of your Bobcat®. It's Genius!
What is amazing about this is that we have taken our engineering to another level. This controller features a unique latching circuit so that you do not have to hold your thumb down for 8 hours for continuous operation.
It works like this: Plug in our controller and your switching paddles will be transformed. On your left paddle, touch the bottom part of the paddle and it works in a momentary fashion. Touch the top and it latches. Touch either the top or bottom and it releases. The same goes for the right paddle. Amazing, right? This was all done because of feedback from customers like you. Now you can run accessories like sprayers, lighting and accumulators without holding your thumb down for hour after hour while trying to run your machine. Genius, pure Genius!!!
Takes about 1 minutes to install. Is 100% plug and play. This configuration is a plug mount so you can use it over and over on any attachment that has one or two solenoids to control. This is complete and ready for plug and play directly into any Bobcat® branded machine. It has an indicator LED to show you that you have power and that it is receiving commands from the Bobcat® machine as well as when the paddles are operating correctly.
What is included:
- CanBus Controller with 2 outputs via 2 x Deutsch DT06 Plugs. Up for latching or down momentarily control from your left stick for plug A. Up for latching or down momentarily control from your right stick for plug B.
- John Deere 3 Pin Adaptor. SG-DTR2A-JD03
- 2 x 2 Pin DT06 Deutsch receptacles with an 18" pigtail to connect to your attachment solenoids from the controller.
- Easy to Follow Instructions
- Incredible factory support that is not available anywhere but from Genius.
Read more about how this product functions here.
This is not just a plug in adapter. There is a microprocessor with software loaded along with a IC driver circuit that enables this to work. That is why it costs more than just a plain old connector.
Bobcat Versahandler 923 - DOES NOT WORK WITH THIS MODEL BECAUSE IT DOES NOT HAVE AN ACD CONTROLLER.
This is not a Bobcat® product. This product is not endorsed by Bobcat®. We are in no way attempting to make you think this is a Bobcat® product. This product is optically isolated from the controls of your machine and can in no way damage your machine or controls. It is perfectly safe to use and will not damage a thing. If a dealer is attempting to tell you that your warranty will be voided if you use this product or that it will damage your machine, please call and report it to us. Skid Steer Genius is a specialty controls company. Our goal is to make anything you buy for your machine work on any machine. Others design and build in such a way as to stop you from doing this.
Bobcat®, the Bobcat logo and the colors of the Bobcat machine are registered trademarks of Bobcat Company in the United States and various other countries.
Bobcat Company is a subsidiary of Doosan Infracore Bobcat Holdings Co., Ltd., a wholly owned subsidiary of Doosan Infracore Co., Ltd.
All rights reserved.
We Also Recommend
SG-CB-6014 - Genius 7 Pin (6 Output) Controller For Bobcat® Loaders, Toolcat & Versahandler - 6 Port | Skid Steer Genius
SG-CB-4000A-100 - Genius 7 Pin Controller For Bobcat® Loaders, Toolcat & Versahandler - 4 Port | Skid Steer Genius
SG-CB-4008 - Genius 7 Pin (4 Output) | 8 Pin Output Controller For Bobcat® Loaders, Toolcat & Versahandler - 4 Port | Skid Steer Genius
SG-CB-2000A-100 - Genius - 7 Pin Controller For Bobcat® Loaders - 2 Port | Skid Steer Genius
QUESTIONS & ANSWERSAsk a Question
Will this fit my 2020 371g I have 3 pin male on my skid. I have a bob cat broom I need to run
How do i get on the waiting list?
Send us your information.
when will this be back in stock?
How soon you guys are able to get this item delivered. Need it ASAP. Using it with a John Deere 3 Pin Connector and a Bobcat T66 7 Pin.
They are due any day. Send us your details and we will add you to the waiting list.
When will this be back in stock
Any day now.
Have a 2011 John Deere 318D want to use a bobcat blower do you have a adapter for the John Deere to bobcat
john deere sb72b snowblower is this the correct adapter harness to us on a tool cat with the 7 pin connector?
No it is not. This adapter provides only 2 ouputs so you can only operate one function. You need a minimum of 4 functions.
You have not told us what kind of connector is on the snow blower so we are going to guess that you have a 14 pin. If that is the case, this is the controller that you need.
Is there another way other than buying this high dollar cord
It is definately not a high dollar cord. It took us years to perfect this computer that decodes the signals that Bobcat purposely built to lock you out of using any attachment but theirs. You can buy one of the Bobcat computers and install it into your attachment for about $1500 otherwise you are stuck with our expensive cord.