Genius 7 Pin (6 Output) 10 Pack - Controller For Bobcat® Loaders, Toolcat & Versahandler - 6 Port | SG-CAN60-14
Pack of 10 SG-CAN60-14
NEW FOR 2024. Our updated 6014 has been designed from the bottom up.
Accepting orders for delivery in late MAY 2024. If you cannot wait for this product, please do NOT order it.
We have had non stop issues with our 6014's buying parts for 3 years because we originally designed it using automotive drivers and microprocessors. The CAN60 uses industrial drivers and processors which have several sources and are easy to get so our shortages will soon be over.
We have also changed manufacturers who are able to assemble these in a much more robust and efficient manner.
The CAN60 Features Include:
- Software guaranteed to operate on all Bobcat machines which include Pilot Control, Hand/Foot Control, Toolcat, Versahandler and now the Imported Bobcat machines from the Czech Republic.
- A molded plastic housing with extra cable retention. NO MORE RESIN, YAY!
- Cable retention whereby the connectors will tear off first if you have an accident, so it can be repaired.
- Embedded 2 x 125 b. magnets to hold it onto your machines frame in multiple locations.
- Higher and lower temperature tolerance.
- 9 Amp output per channel which is regulated to 15 amps max to protect your machines fuse.
- 2 x channels can be programmed to latch. C,D (A1/A2).
- Latching programming has been simplified.
- A more common sense LED output makes it easy to see what is going on with the controller.
- Extra output protection from Chinese dirty solenoids.
This is a true Genius Controller designed for solenoid controls only.
The CAN60 is a 6 output controller with a 14 pin connector pinned the old fashioned way. Using the old Bobcat 14 pin layout which works with Takeuchi, Gehl, Kubota, Mustang, Case, New Holland attachments up to 6 controls plugs K pin power.
Cat D-Series requires moving the pins G to A and H to J. If your attachment is set up for high flow, you will need to push the K pin back so the HF sense is not connected. This is a ground wire in Cat attachments whereby it is a +12volt in Bobcat so you will blow your fuse if you leave it connected.
Outputs include:
- A1/A2 - Pin C/D one or both can latch while the others will remain momentary.
- B1/B2 - Pin E/F momentary only.
- C1/C2 - Pin G/H momentary only.
- B - Ground & K is constant output.
Because of fuse and circuit limitations, any combination of 2 will work at the same time. If you try to make three latch, the circuit will reset and you will have to reprogram the adapter. This adapter ships with all outputs set up for momentary only.
This adapter is specially designed to plug into any Bobcat® 7 Pin connector and allow the operator to run up to 6 x 12 volt solenoids directly from the stick controls of your Bobcat®. Works on Bobcat® skid steer loaders as well as Toolcat and Versahandler machines.
Takes about 1 minute to install. Is 100% plug and play. This configuration is for boom mount so you can use it over and over on any attachment that has up to 6 solenoids to control. This is complete and ready for plug and play directly into any Bobcat® branded machine. It has power, communication, and a port status indicator LED to show you that it is working and that it is receiving commands from the Bobcat® machine.
Throw away the crappy control box that the manufacturers supply and switch over to true machine controls.
How to program:
Channels C & D ship as momentary controls but if you would like them to operate like a locking switch you can program each one individually to latch. With the key off, select either A1 or A2 and hold it down while you turn on the machine. Continue to hold for 5 seconds until you see the LED's flash. It is now programmed and ready to go.
CLICK HERE TO DOWNLOAD THE USER MANUAL
Bobcat 2020+ Versahandler 923 - DOES NOT WORK WITH THIS MODEL BECAUSE IT DOES NOT HAVE AN ACD CONTROLLER.
Disclaimer:
This is not a Bobcat® product. This product is not endorsed by Bobcat®. We are in no way attempting to make you think this is a Bobcat® product. This product is optically isolated from the controls of your machine and can in no way damage your machine or controls. It is perfectly safe to use and will not damage a thing. If a dealer is attempting to tell you that your warranty will be voided if you use this product or that it will damage your machine, please call and report it to us. Skid Steer Genius is a specialty controls company. Our goal is to make anything you buy for your machine work on any machine. Others design and build in such a way as to stop you from doing this.
Bobcat®, the Bobcat logo and the colors of the Bobcat machine are registered trademarks of Bobcat Company in the United States and various other countries.
Bobcat Company is a subsidiary of Doosan Infracore Bobcat Holdings Co., Ltd., a wholly owned subsidiary of Doosan Infracore Co., Ltd.
All rights reserved.
We Also Recommend
Customer Reviews
QUESTIONS & ANSWERS
Have a Question?
Be the first to ask a question about this.