Genius - Single Switch Kit - SG-SW1-240 | Skid Steer Genius
Many people just need one switch added to their machines so they can operate a single solenoid. Well here it is. Just add power, run the cable extension out to your boom and connect to any single solenoid operated attachment. Our switch kit is an industrial grade switch with gold contacts guaranteed for 1 million cycles. This switch has been hermetically sealed inside a silicone boot to protect it from water, dirt and oil.
Included in this kit:
- Switch kit with zip ties to hold it onto your stick (FV-309-704)
- Cable Extension (20 Feet) to reach out to the end of your boom (SG-DTR-DTP-240) with zip ties to hold cable in place
Depending on your machine, you may need some other accessories to install this kit. You will need to connect to the battery or an open fuse position inside your cab. A key switch position is the best so that you do not leave your circuit hot while your machine is turned off.
General Installation Instructions:
Every customers need and machine is different so we can't be specific in out installation instructions. I your kit, you have the main button harness. You are meant to install this on your left stick using the supplied zip ties. Run the feed harness down and out until you find a power source such as a cigarette light plug. Connect this end to the power source. You can use splice connections or adapter plugs. Make sure you tape up your connections well so you do not cause a short and blow your fuse.
Next you will take the plug end of the harness and add the 25 foot extension harness. You will route this harness carefully out the boom following the hydraulic lines to where your hydraulic couplers terminate on the boom. Make sure all of the wires are tucked in so they do not get snagged and that they have zip ties installed so there is no way they can come loose.
The attachment should have a similar 2 pin connection installed so you can easily connect it to the switch extension when in use. Test by pushing the button and listening for the clicking sound of the control solenoid or with a test light.
We Also Recommend
QUESTIONS & ANSWERSAsk a Question
Is this the proper kit to install a grouser 6 way dozer blade on a bobcat s630 skid steer? thanks.
That will work. Or this.
hello i have a 2020 331g Deere I just bought a land honor 9 ft scraper attachment it has 3 solenoids to 3 run cylinders do you sell a kit so i can run it?
Chinese attachments are being dumped on RB Auctions in record numbers. As of the publish dates, these are the brands. Generally, they dump them at auctions, they don’t work so they change the brand name and start dumping again. This is really a case of you get what you pay for. Shame on RB for allowing this to happen! A few items will last a while but when they blow, you will need a machine shop to manufacture the parts since companies do not exist. If there is an address, it is fake or a mail drop. I am putting them all on one page since most items are the same, they just have a different name stuck on them.
Land Honor, Wolverine, Great Bear, Suihe, Top Cat, Mower King, TMG, American Manufacturing
NOTE: These companies do not exist so don't waste your time trying to contact them because you are on your own. All materials are China sourced so you will need to fabricate your own repairs, but hey they are cheap to buy.
For all Chinese Attachments:
Verify the voltage of the solenoids as many of them ship with 24 volt solenoids. You must replace the solenoid coils with 12 volt rated ones for the attachments to work. Here is a link to replacement coils.Click Here to Order a Replacement 12 Volt Coil
Land Honor Grader - Possibly 24 volt Solenoids - You must verify and contact us for a resolution.
6 Solenoids – Deutsch ConnectionsClick Here and Choose the Deutsch Option for all 14 pin machines like Kubota, Cat D, New Holland, Case, John Deere, Takeuchi
I want to use the Wolverine concrete mixer on my Kubota tractor (not skid steer) with front hydraulics. Would this kit work for me and what else would I need? What do I need for a connection to the Wolverine wires coming off the actuator?
This is the kit that we use. I do not know the configuration of your tractor so I cannot guarantee that the lengths will be correct.
I have a paladin power rake and need a switch to operate the angle hydraulics
Usually the modern ones have two solenoids so a single switch will not work. How about this?